Especificaciones para Chassis Nuevo Combinacion Dos Chassis B-Train
Chassis Nuevo Fabricado por Cheetah Chassis en USA.
| Front Chassis | |
| Function | Carries one 20 ft ISO Container. Meets all DOT, TOFC, AAR, CMVSS, ANSI, SAE and TTMA specifications in effect at the time of manufacture and applicable to operation in Canada. |
| Overall Length Extended | 29 ft. 3 inches |
| Overall Length Closed | 22 ft. 2 inches |
| Overall Width | 96 inches over bolsters {102 over tires} |
| Tandem Location | 63 1/4 inches |
| Kingpin Location | 15 inches from front of chassis |
| Kingpin Height | 48 inches |
| Slide Range | 85 3/8 inches |
| Maximum Rear Height | 51 inches |
| Main Beams | Fabricated I-Beam with 1/2 inch x 4 inch top and 5/8 inch x 4 inch bottom flanges and 1/4 inch web |
| Forward Beams | Fabricated I-Beam with 1/2 inch x 4 inch top and 5/8 inch x 4 inch bottom flanges and 1/4 inch web |
| Slider Beams | Fabricated I-Beam with 5/8 inch x 4 inch top and bottom flanges and 1/4 inch web. |
| Cross Member | All cross members are formed from 7-gauge steel. |
| Upper Coupler Assembly | Pick up plate is 5/16” thick and extends approximately 18” behind the kingpin and is reinforced fore and aft by 5/16 inch formed channels |
| Front Bolsters | Box type with 3/8 inch x 8 inch top plate and 5/16 inch thick, formed channel lower member. |
| Rear Bolster | Low profile Box type with 1/2 inch x 8 inch top and bottom plates. |
| Twist Lock & Slide Pins | Meets ISO standards and requirements |
| Slider Mechanism | Lock engagement ensured by two spring-loaded pins through main beams. A weld washer secured polyethylene slide pad facilitates sliding. Air activated locking pin. |
| Fifth Wheel | Holland 3500 |
| Fifth wheel location from rear of chassis | 32 3/8 inches |
| ICC Bumper | 4 inch x 4inch x 3/16 inch Tube step bumper. Main beam and bumper struts are extended 2 inches to protect rear bolster. (No rubber dock bumpers) |
| Landing Gear | Two speed AAR approved, square leg.50,000 lb. lift capacity and 140,000 static load capacity. |
| Landing Gear Axle Type | Standard |
| Landing Gear Foot Group | 10 in. by 10 in. Low profile sandshoe |
| Crank Handle Location | Curb side handle |
| Axle Quantity | Two Axles |
| Suspension Type | Spring-Ride |
| Axle Centers | 72 1/2 inch |
| Springs | Three Leaf |
| Hub Type | Hub piloted for disc wheels |
| Hub Material | Steel |
| Drum | Outboard mounted |
| Rims/Wheel | 8 1/4 X 22.5 hub piloted tubeless |
| Wheel/Rim Color | White |
| Tires | Cheetah Supplied |
| Tire Size | 11R 22.5 |
| Tire Inflation System | None |
| Axle Type | TN |
| Wall Thickness | 1/2 inch |
| Axle Track | 77.5 |
| Brake Lining Options | Standard |
| Lubrication | Oil 90 wt. |
| Slack Adjusters | Automatic |
| Brake System Type | 2S1M |
| Brake Chambers | 30/30 |
| Hubodometer | None |
| Electrical System | 12 volt, 7-way split pin receptacle plug; modular wiring harness |
| Light Attachment | Grommet mounted |
| Light Type | LED |
| Metal Preparation | Clean, dry steel and NACE No. 3 /SSPC-SP-6 “Commercial Blast Cleaning” |
| Primer | 70% Zinc Rich Primer |
| Topcoat | Urethane Topcoat |
| Color | Black |
| Markings | FHWA plate, tare weight, 2 small Cheetah logos. |
| Customer Decals | Furnished by Customer |
| Conspicuity | Meets DOT requirements |
| Registration Holder | Plastic with clear screw on top |
| Mud Flaps | Cheetah Supplied |
| Mud Flap Mounting | 4 mounting bolts |
| Steel & Fasteners | All structural steel is ASTM-A572, Grade 50, or ASTM-A607, Grade 50.All structural fasteners are Grade 5 or better and are zinc coated |
| GVWR | 59,000 lbs |
| Weight | Approximately 8,400 lbs. + 2% |
| Rear Chassis | |
| Function | Carries one 20 ft ISO Container Meets all DOT, TOFC, AAR, CMVSS, ANSI, SAE and TTMA specifications in effect at the time of manufacture and applicable to operation in Canada. |
| Overall Length | 31 ft. 9 inches |
| Overall Width | 96 inches |
| Tridem Location | 86 inches |
| Kingpin Location | 15 inches from front of chassis |
| Kingpin Height | 47 1/2 to 48 inches |
| Maximum Rear Height | 48 inches |
| Main Beams | Fabricated I-Beam with 1/2 inch x 4 inch top and bottom flanges and 1/4 inch web. 6 1/2 inch front, 14inch main. |
| Cross Member | All cross members are formed from 7-gauge steel. |
| Upper Coupler Assembly | Pick up plate is 5/16” thick and extends approximately 18” behind the kingpin and is reinforced fore and aft by 5/16 inch formed channels |
| Front Bolsters | Tube type with 6 inch x 8 inch x 5/16″. |
| Rear Bolster | Box type with 3/8 inch x 8 inch top plate and 5/16 inch thick, formed channel lower member. |
| Twist Lock & Slide Pins | Meets ISO standards and requirements |
| ICC Bumper | 4 inch x 4inch x 3/16 inch Tube step bumper. Main beam and bumper struts are extended 2 inches to protect rear bolster. (No rubber dock bumpers) |
| Landing Gear | Two speed AAR approved, square leg. 50,000 lb. lift capacity and 140,000 static load capacity. |
| Landing Gear Axle Type | Solid Axle |
| Landing Gear Foot Group | 10 in. by 10 in. Low profile sandshoe |
| Crank Handle Location | Road side handle |
| Axle Quantity | Three Axles |
| Suspension Type | Spring-Ride |
| Axle Centers | 60 inch |
| Springs | Three Leaf |
| Hub Type | Hub piloted for disc wheels |
| Hub Material | Steel |
| Drum | Outboard mounted |
| Rims/Wheel | 8 1/4 X 22.5 hub piloted tubeless |
| Wheel/Rim Color | White |
| Tires | Cheetah Supplied |
| Tire Size | 11R 22.5 |
| Tire Inflation System | None |
| Axle Type | TN |
| Wall Thickness | 1/2 inch |
| Axle Track | 71.5 |
| Brake Lining Options | Standard |
| Lubrication | Oil 90 wt. |
| Slack Adjusters | Automatic |
| Brake System Type | 2S1M |
| Brake Chambers | 30/30 |
| Hubodometer | None |
| Electrical System | 12 volt, 7-way split pin receptacle plug; modular wiring harness |
| Light Attachment | Grommet mounted |
| Light Type | LED |
| Metal Preparation | Clean, dry steel and NACE No. 3 /SSPC-SP-6 “Commercial Blast Cleaning” |
| Primer | 70% Zinc Rich Primer |
| Topcoat | Urethane Topcoat |
| Color | Black |
| Markings | FHWA plate, tare weight, 2 small Cheetah logos. |
| Customer Decals | Furnished by Customer |
| Conspicuity | Meets DOT requirements |
| Registration Holder | Plastic with clear screw on top |
| Mud Flaps | Cheetah/Markham |
| Mud Flap Mounting | 4 mounting bolts |
| Steel & Fasteners | All structural steel is ASTM-A572, Grade 50, or ASTM-A607, Grade 50. All structural fasteners are Grade 5 or better and are zinc coated |
| GVWR | 60,000 lbs |
| Weight | Approximately 9,000 lbs + 2% |
